The fewer times the signals bounce off surfaces like walls, trees, and hills to get to your antenna, the clearer your reception. Try and aim towards a transmission tower by mounting your antenna on a perfectly vertical mast. If you can install your outdoor antenna on the roof, the better.

This is because you’ll be reducing obstacles for the signal to come to the antenna. In addition to reducing interference, you’ll also have access to more channels. Therefore, if you want the clearest signal to watch your favorite shows, consider setting your TV antenna to the highest position possible. The higher you go, the better the TV signal reception. Therefore, placing your antenna near the window can reduce the interference. This is because ceilings and walls are obstructions to the TV signals. Nonetheless, consider placing it near your window if you have an indoor antenna. It’s a common misconception that indoor antennas are not as effective as outdoor antennas. So, how can you fix that? Ensure that your TV antenna is at least six feet away from these metallic surfaces. Reflective surfaces can weaken or even completely block your TV signals.įor indoor antennas, surfaces like bug screens or burglar bars can block the TV signals. If your TV antenna is up on the roof, the metal roof surface could be causing the interference. These have FM traps that can block these annoying signals. If you feel that you clearly fall under this category, consider getting a preamplifier. Radio signals are likely your culprit if you live near an FM station. Install it between your TV and the end of your antenna’s coaxial cable. If this is the case, kindly consider getting an LTE filter to protect your TV antenna from these signals. If not, we’re here to tell you anyway so that you can find out if that’s what’s causing your TV interference.Ĭell phone signals use 4G Long Term Evolution (LTE) that can interfere with your TV stations and UHF channels. You’ve probably ever wondered how your smartphone works. This will allow you to know if that’s what’s causing the interference. Once you’ve done that, run your microwave or hairdryer and see if your TV signal is affected. Make sure that the coaxial cable doesn’t touch or run closely perpendicular or parallel to any electrical cables. First, check the antenna and the coaxial cable that runs to your TV. So, how do you fix this situation?ĭuring the next blackout, the best thing to do is to check the entire system. You may go into the kitchen to warm your food for the game only to come to face white noise.

This is especially the case if your home wiring is the old wiring system where the electromagnetic shielding is poor. Some electromagnetic appliances in your home that may be messing up your TV signal include microwaves and hair dryers. These interferences come in many forms, and we’ll look at how to deal with a few. Interferences close to your TV antenna can be a major cause of you not enjoying the TV stations you love. Ways to Boost TV Antenna Signal Homemade 1. If these methods don’t work, then you can go out and get some equipment to help. You can have the best TV antenna but this doesn’t always guarantee you the best service.Īnd although you can go to the store, online or physical, and get an amplifier to boost your Antenna, we thought we’d look at some free options first. I found out this is a line amplifier,to boost signals for long cable runs,but it works well as an antenna amp.I tried different transistors and found that ge222's worked well.What are some ways to boost your TV antenna signal? We’ll cover how to boost TV antenna signal homemade in this detailed guide. The b lead of the first transistor is connected to a line of sockets that are connected together under the prototype board,so the component leads put through the holes will be connected together.There are four such lines,(with the E lead of each transistor connected to the negative power feed).So it's transistor,resistor,capacitor for left side transitor, and again for the right side.A capacitor on the left to feed the antenna input,a capactor to bridge the first pair to the second pair of circuit traces,and a third capacitor on the rightmost line to output the amplified signal.On the rightmost line of each pair is a resistor,3.3K for left pair,1K for right pair that connect to the positive power feed.The input capacitor connencts to the first resistor on left,the output capacitor is at the capacitor of the second pair on rightmost line or between the capacitor and the topmost resistor of the second pair of circuit connection lines.

The drawing above the blurry,very blurry,photo shows it well,although you might want to magnify the image with ctrl +.

Homemade tv antenna signal booster